Lutron Caseta Diva Smart Dimmer Switch vs Sonoff Orb-ZBRBS Zigbee Smart Roller Shutter Wall Switch

Zigbee 3.0 on an EFR32MG21 MCU. It is a Zigbee end device that also repeats the mesh for nearby devices, but it still needs a coordinator such as a SONOFF ZBBridge-P, ZBBridge-U, NSPanel Pro, iHost or a ZBDongle-P/-E.

Lutron documents that the Diva's status LED can be switched on or off from the Lutron app (it is on by default), and the same screen adjusts the dimmer's high-end and low-end trim

Power failure memory: should power be interrupted, the control returns to the level it was set to before the interruption

The dimmer is wired to the load it controls; the wire-free half of the system is the separate Pico remote or the Claro accessory switch

Lutron lists Amazon Alexa among the platforms Caseta works with, through the Lutron Smart Hub

SONOFF's product page shows the eWeLink app linking to Amazon Alexa, and the knowledge center lists Alexa among the third-party platforms for voice control.

Lutron lists Apple Home among the platforms Caseta works with; the Apple Home technology sits in the smart hub, so Siri controls the dimmer once it is paired to one

The Orb-ZBRBS has no native HomeKit profile. Its knowledge center documents adding it to Apple Home through a software-based Matter bridge, the eWeLink CUBE or a SONOFF Zigbee Bridge Ultra.

Lutron lists Google Assistant among the platforms Caseta works with, through the Lutron Smart Hub

SONOFF's product page shows the eWeLink app linking to Google Home, and the knowledge center lists Google Home among the third-party platforms the device syncs to through the eWeLink cloud.

The core Lutron Caseta integration connects to the Lutron Caseta Smart Hub (L-BDG2-WH) and exposes wall dimmers as lights

SONOFF documents Home Assistant for this model both through the eWeLink account and directly over Zigbee using ZHA or Zigbee2MQTT with a ZBDongle-P/-E.

The CSA certified-product database holds no Matter certification for Lutron (only three Zigbee 3.0 Aurora dimmers), and Lutron's own Caseta compatibility page never mentions Matter

The switch itself is Zigbee, not Matter. Its product page documents reaching the Matter ecosystem through a SONOFF Zigbee bridge such as the ZBBridge-U or eWeLink CUBE.

Lutron lists Samsung SmartThings among the platforms Caseta works with, through the Lutron Smart Hub

Via Matter: the Orb-ZBRBS is published to Matter by a SONOFF Zigbee bridge (ZBBridge-U or eWeLink CUBE), and SmartThings is a certified Matter controller, so it can control the shutter from that fabric.

Operating voltage 120 V~ 50/60 Hz, listed for the DVRF-6L in Lutron's Caseta load controls specification submittal

The specification table rates the switch at 100-240V~ 50/60Hz 1A Max, and the motor requirements say the roller shutter motor must be an AC 100-240V unit drawing less than 1A.

Dimmable CFL up to 150 W, listed alongside LED in the derating chart of the Diva's own installation guide

No capacitive load support is documented; the device is specified only for AC roller shutter motors.

The specification table rates the device at 1A Max, and SONOFF's motor requirements state the roller shutter motor must draw less than 1A.

Simple two-wire installation, so no neutral wire is needed in the wallbox

SONOFF's FAQ answers it directly: the Orb-ZBRBS requires a neutral wire for proper installation and operation.

Incandescent and halogen loads, 25 W minimum and 600 W maximum when the dimmer is not ganged

The Orb-ZBRBS is a roller shutter controller built for AC tubular motors; the product page and knowledge center document motor loads only, not resistive loads such as heaters or incandescent bulbs.

600 W single gang, derated to 500 W in a double gang and 400 W in a triple gang wallbox